For the troubleshooting, there are driving patterns described below. Driving in the specified pattern allows to diagnose malfunctioning items listed below. After the repair of the following trouble items, be sure to drive the vehicle with the specified drive patterns to check whether the function is resumed correctly.
1. PREPARATION FOR DRIVE CYCLE
1. Check that the battery voltage is 12 V or more and fuel remains approx. half [20 — 40 L (5.3 — 10.6 US gal, 4.4 — 8.8 Imp gal)].
2. After performing the diagnostics and clearing the memory, check for any remaining unresolved trouble data. 
3. Disconnect the delivery (test) mode connector.
NOTE:
• Perform the diagnosis after warming up the engine except when the engine coolant temperature at starting is specified.
• Perform the diagnosis twice if the DTC marked with *. After completing the first diagnosis, stop the engine and perform second diagnosis in same condition.
2. DRIVE CYCLE A — DRIVE THE VEHICLE WITH 80 KM/H (50 MPH) FOR 20 MINUTES, AND THEN IDLE THE ENGINE FOR A MINUTE
|
DTC |
Item |
Condition |
|
*P0125 |
Insufficient Coolant Temperature for Closed Loop Fuel Control |
Engine coolant temperature at engine start is less than 20°C (68°F). |
|
*P0133 |
O2 Sensor Circuit Slow Response (Bank 1 Sensor 1) |
— |
|
*P0171 |
System Too Lean (Bank 1) |
— |
|
*P0172 |
System Too Rich (Bank 2) |
— |
|
*P0301 |
Cylinder 1 Misfire Detected |
Complete diagnosis in drive cycle B or C as well. |
|
*P0302 |
Cylinder 2 Misfire Detected |
Complete diagnosis in drive cycle B or C as well. |
|
*P0303 |
Cylinder 3 Misfire Detected |
Complete diagnosis in drive cycle B or C as well. |
|
*P0304 |
Cylinder 4 Misfire Detected |
Complete diagnosis in drive cycle B or C as well. |
|
*P0420 |
Catalyst System Efficiency below Threshold (Bank 1) |
— |
|
P0459 |
Canister Purge Control Solenoid Valve Circuit High |
— |
|
P0562 |
System Voltage Low |
— |
|
P0563 |
System Voltage High |
— |
3. DRIVE CYCLE B — TEN MINUTES IDLING
NOTE:
Drive the vehicle at 10 km/h (6 MPH) or faster before diagnosis.
|
DTC |
Item |
Condition |
|
*P0171 |
System Too Lean (Bank 1) |
— |
|
*P0172 |
System Too Rich (Bank 2) |
— |
|
*P0301 |
Cylinder 1 Misfire Detected |
Complete diagnosis in drive cycle A or C as well. |
|
*P0302 |
Cylinder 2 Misfire Detected |
Complete diagnosis in drive cycle A or C as well. |
|
*P0303 |
Cylinder 3 Misfire Detected |
Complete diagnosis in drive cycle A or C as well. |
|
*P0304 |
Cylinder 4 Misfire Detected |
Complete diagnosis in drive cycle A or C as well. |
4. DRIVE CYCLE C — DRIVE THE VEHICLE WITH FOLLOWING DRIVE PATTERNS
|
(A) |
Idle the engine for 10 seconds or more. |
(D) |
Decelerate with fully closed throttle to 64 km/h (40 MPH). |
(G) |
Stop the vehicle with throttle fully closed. |
|
(B) |
Accelerate to 97 km/h (60 MPH) within 20 seconds. |
(E) |
Drive the vehicle at 64 km/h (40 MPH) for 20 seconds. |
(H) |
Vehicle speed km/h (MPH) |
|
(C) |
Drive the vehicle at 97 km/h (60 MPH) for 20 seconds. |
(F) |
Accelerate to 97 km/h (60 MPH) within 10 seconds. |
(I) |
Sec. |
|
DTC |
Item |
Condition |
|
*P0030 |
HO2S Heater Control Circuit (Bank 1 Sensor 1) |
— |
|
P0134 |
O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1) |
— |
|
*P0171 |
System Too Lean (Bank 1) |
— |
|
*P0172 |
System Too Rich (Bank 2) |
— |
|
*P0244 |
Turbo/Super Charger Wastegate Solenoid “A” Range/Performance |
— |
|
P0246 |
Turbocharger Wastegate Solenoid A High |
— |
|
*P0301 |
Cylinder 1 Misfire Detected |
Diagnosis completes in drive cycle A or B as well. |
|
*P0302 |
Cylinder 2 Misfire Detected |
Diagnosis completes in drive cycle A or B as well. |
|
*P0303 |
Cylinder 3 Misfire Detected |
Diagnosis completes in drive cycle A or B as well. |
|
*P0304 |
Cylinder 4 Misfire Detected |
Diagnosis completes in drive cycle A or B as well. |
|
P2004 |
Intake Manifold Runner Control Stuck Open (Bank 1) |
— |
|
P2005 |
Intake Manifold Runner Control Stuck Open (Bank 2) |
— |
1. Remove the battery negative terminal, and reconnect after 10 seconds have passed.
2. Start the engine and warm up engine until coolant temperature is 80°C (176°F).
3. Start the engine and warm up engine until coolant temperature is 40°C (104°F) or less.
NOTE:
Do not let engine coolant temperature drop below 5°C (41°F).
4. Start the engine and warm up engine until coolant temperature is 80°C (176°F).
5. Start the engine and warm up engine until coolant temperature is 40°C (104°F) or less.
NOTE:
Do not let engine coolant temperature drop below 5°C (41°F).
6. Start and idle the engine.
|
DTC |
Item |
Condition |
|
*P0410 |
Secondary Air Injection System |
— |
|
P0414 |
Secondary Air Injection System Switching Valve “A” Circuit Shorted |
— |
|
P1418 |
Secondary Air Injection System Control “A” Circuit Shorted |
— |
|
*P2441 |
Secondary Air Injection System Switching Valve Stuck Closed (Bank 1) |
— |