LAN SYSTEM (DIAGNOSTICS) > Read Current Data
|
Items to be displayed |
Unit of measure |
Description |
Note |
|
BATT voltage (control) |
10 — 15 V |
Body integrated unit input value |
Always |
|
BATT voltage (BACKUP) |
10 — 15 V |
Body integrated unit input value |
Always |
|
IG power supply voltage |
10 — 15 V |
Body integrated unit input value |
Ignition switch ON |
|
ACC voltage |
10 — 15 V |
Body integrated unit input value |
Ignition switch ACC |
|
Illumination VR Voltage |
0 — 5 V |
Body integrated unit input value |
Input value from illumination volume |
|
Illumi. output d-ratio |
0 — 100% |
Body integrated unit output value |
Small light ON Illumination volume is other than bright. |
|
Ambient Temperature |
−40 — 87.5°C |
CAN data input value |
Ignition switch ON |
|
Fuel level voltage |
0 — 8 V |
Body integrated unit input value |
Ignition switch ON |
|
Fuel level resistance |
0 — 102.3 Ω |
Body integrated unit input value |
Ignition switch ON |
|
key-lock solenoid V |
6 — 12 V |
Body integrated unit output value |
Key warning switch ON, other than parking range Ignition ON (except for model with keyless access) |
|
number of regist. |
0 — 4 |
Number of keyless key registered |
(except for model with keyless access) |
|
Front Wheel Speed |
km/h |
CAN data input value |
Reception from VDC module |
|
VDC/ABS latest f-code |
DTC display (Temporarily) |
CAN data input value |
It is normal when DTC is not been input even if this code is displayed. Reception from VDC (Use after hexadecimal conversion) |
|
Blower Fan Steps |
0 — 2 levels |
CAN data input value |
0: OFF, 1: Low, 2: 2 levels or more Reception from air conditioner ECM |
|
Fuel level resistance 2 |
0 — 102.3 Ω |
CAN data output value |
Reception from body integrated unit |
|
Fuel consumption |
cc/s |
CAN data input value |
Reception from ECM and transmission to center monitor |
|
Coolant Temp. |
−40 — 130°C |
CAN data input value |
Reception from ECM |
|
Vehicle longitudinal G |
m/s2 |
CAN data input value |
Reception from VDC module |
|
SPORT Shift Stages |
0 — 7 levels |
CAN data input value |
(0: Light OFF; 1 — 5: Gear display; 6: Fail; 7: ATF temperature High/Low) Reception from TCM |
|
Shift Position |
0 — 7 levels |
CAN data input value |
0: 1, 1: 2, 2: 3, 3: 4, 4: D, 5: N, 6: R, 7: P shift position (8 indicates no input) 8 is displayed in manual mode Reception from TCM |
|
VDC/ABS condition |
0 — 4 |
CAN data input value |
Reception from VDC/ABS |
|
Destination Code |
0 — 16 |
CAN data input value |
Reception from combination meter |
|
Touch SW |
0 — 64 |
CAN data input value |
Reception from navigation module |
|
key-lock warning SW |
ON/OFF |
Body integrated unit input value |
ON when ignition key inserted (except for model with keyless access) |
|
Stop lamp SW |
ON/OFF |
Body integrated unit input value |
ON when brake pedal is depressed |
|
Front fog lamp SW input |
ON/OFF |
Body integrated unit input value |
When front fog light switch is ON |
|
Rear fog lamp SW input |
ON/OFF |
Body integrated unit input value |
When rear fog light switch is ON |
|
Door key-lock SW input |
ON/OFF |
Body integrated unit input value |
Applied for EK |
|
Door unlock SW input |
ON/OFF |
Body integrated unit input value |
Applied for EK |
|
Driver’s door SW input |
ON/OFF |
Body integrated unit input value |
ON when driver’s door is open |
|
P-door SW input |
ON/OFF |
Body integrated unit input value |
ON when passenger’s door is open |
|
Rear right door SW input |
ON/OFF |
Body integrated unit input value |
ON when rear right door is open |
|
Rear left door SW input |
ON/OFF |
Body integrated unit input value |
ON when rear left door is open |
|
R Gate SW input |
ON/OFF |
Body integrated unit input value |
ON when rear gate/trunk open |
|
Manual lock SW input |
ON/OFF |
Body integrated unit input value |
Manual lock switch ON |
|
Manual unlock SW input |
ON/OFF |
Body integrated unit input value |
Manual unlock switch ON |
|
Lock SW |
ON/OFF |
Body integrated unit input value |
Applied for EK |
|
Bright SW input |
ON/OFF |
Body integrated unit input value |
ON when bright switch is ON (only for model with clock) |
|
Economy Switch |
ON/OFF |
Body integrated unit input value |
Except for SI drive |
|
P SW |
ON/OFF |
Body integrated unit input value |
ON when shift range is in parking Shift lever P switch signal |
|
MT Reverse Switch |
ON/OFF |
Body integrated unit input value |
ON when shift is in reverse |
|
R wiper ON SW input |
ON/OFF |
Body integrated unit input value |
Rear wiper switch ON |
|
R wiper INT SW input |
ON/OFF |
Body integrated unit input value |
Rear wiper switch (INT ON) |
|
R washer SW input |
ON/OFF |
Body integrated unit input value |
Rear washer switch ON |
|
wiper deicer SW input |
ON/OFF |
Body integrated unit input value |
Wiper deicer switch ON |
|
Rear Defogger SW |
ON/OFF |
Body integrated unit input value |
Wiper deicer switch ON |
|
Driver’s Seat SW input |
ON/OFF |
Body integrated unit input value |
Driver’s seat buckle switch ON |
|
P seatbelt SW input |
ON/OFF |
Body integrated unit input value |
Passenger’s seat buckle switch ON |
|
Fr wiper input |
ON/OFF |
Body integrated unit input value |
ON when front wiper is operating |
|
Parking Brake Switch Input |
ON/OFF |
Body integrated unit input value |
When parking brake locked |
|
Registration SW input |
ON/OFF |
Body integrated unit input value |
With keyless registration connector connected (except for model with keyless access) |
|
Driver’s seat lock status SW input |
ON/OFF |
Body integrated unit input value |
Displays latch state, ON when locked (only for model with keyless access) |
|
Passenger’s seat lock status SW input |
ON/OFF |
Body integrated unit input value |
Displays latch state, ON when locked (only for model with keyless access) |
|
R gate lock status SW input |
ON/OFF |
Body integrated unit input value |
Displays latch state, ON when locked |
|
Smart wake-up input |
ON/OFF |
Body integrated unit input value |
ON when wake-up signal is received from gateway CM. (only for model with keyless access) |
|
R Gate Release SW input |
ON/OFF |
Body integrated unit input value |
Rear gate opener button ON |
|
Rr defogger output |
ON/OFF |
Body integrated unit output value |
ON when rear defogger relay is operating |
|
lock actuat. LOCK output |
ON/OFF |
Body integrated unit output value |
ON when LOCK signal is output |
|
All seat UNLOCK output |
ON/OFF |
Body integrated unit output value |
ON when unlock signal is output |
|
D-seat UNLOCK output |
ON/OFF |
Body integrated unit output value |
ON when unlock signal is output |
|
R gate/trunk UNLK output |
ON/OFF |
Body integrated unit output value |
ON when rear gate/trunk unlock signal is output |
|
Double lock output |
ON/OFF |
Body integrated unit output value |
Applied for EK, KA |
|
R wiper output |
ON/OFF |
Body integrated unit output value |
ON when rear wiper motor is operating |
|
Shift Lock Solenoid |
ON/OFF |
Body integrated unit output value |
ON when shift lock solenoid is operating (only AT) |
|
Key locking output |
ON/OFF |
Body integrated unit output value |
With ignition switch ON and in other than the shift P range, with key in switch ON (except for model with keyless access) |
|
wiper deicer output |
ON/OFF |
Body integrated unit output value |
ON when wiper deicer relay is operating |
|
Hazard Output |
ON/OFF |
Body integrated unit output value |
ON when answer-back signal is received or when hazard is operating |
|
Horn Output |
ON/OFF |
Body integrated unit output value |
ON when security warning is operating |
|
P-belt warning light O/P |
ON/OFF |
Body integrated unit output value |
ON when Ignition switch is turned to ON, occupant is seated, and buckle switch is turned off |
|
Illumination lamp O/P |
ON/OFF |
Body integrated unit output value |
ON when illumination is illuminated |
|
Room lamp output |
ON/OFF |
Body integrated unit output value |
ON when keyless lock/unlock signal is received (when keyless switch connector is removed) |
|
key illumi. lamp o/p |
ON/OFF |
Body integrated unit output value |
ON when key illumination light is illuminated (only for model with keyless access) |
|
R fog lamp output |
ON/OFF |
Body integrated unit output value |
Rear fog light switch ON |
|
R fog lamp monitor |
ON/OFF |
Body integrated unit output value |
When rear fog light relay is ON |
|
Immobilizer lamp output |
ON/OFF |
Body integrated unit output value |
ON when immobilizer pilot light blinks |
|
Keyless operation 1 |
Regist./Normal |
Body integrated unit input value |
When keyless registration connector is connected (except for model with keyless access) |
|
Keyless operation 2 |
Deletion/Normal |
Body integrated unit input value |
When keyless registration is deleted (except for model with keyless access) |
|
EK alarm output |
ON/OFF |
Body integrated unit output value |
When EK alarm output |
|
CC Main Lamp |
ON/OFF |
CAN data input value |
Cruise control switch ON Reception from ECM and transmission to combination meter |
|
CC Set Lamp |
ON/OFF |
CAN data input value |
ON when cruise control vehicle speed is set Reception from ECM and transmission to combination meter |
|
SPORT Lamp |
ON/OFF |
CAN data input value |
SPORT mode switch ON Reception from TCM and transmission to combination meter (only AT) |
|
SPORT Blink |
Blink/OFF |
CAN data input value |
Blinks when there is an AT failure Reception from TCM and transmission to combination meter (only AT) |
|
ATF Temperature Lamp |
ON/OFF |
CAN data input value |
When ATF temperature rise (only AT) |
|
ATF Blink |
Blink/OFF |
CAN data input value |
Blinks when there is an AT failure Reception from TCM and transmission to combination meter (only AT) |
|
Tire diameter abnormal 1 |
ON/OFF |
CAN data input value |
Lit when FWD fuse is connected (4AT only) |
|
Tire diameter abnormal 2 |
Blink/OFF |
CAN data input value |
Blinks when the difference in rotation between front and rear wheels is 4% or more Reception from TCM and transmission to combination meter (only AT) |
|
Shift Up Indication |
UP/OFF |
CAN data input value |
ON when shift lever up-operation is possible (received from TCM) |
|
Shift Down Indication |
DOWN/OFF |
CAN data input value |
ON when shift lever down-operation is possible (received from TCM) |
|
SPORT Shift (buzzer 1) |
ON/OFF |
CAN data input value |
ON while the shift change prohibited warning buzzer is operating Reception from TCM and transmission to combination meter (only AT) |
|
SPORT Shift (buzzer 2) |
ON/OFF |
CAN data input value |
ON when the ATF high temperature warning buzzer is operating Reception from TCM and transmission to combination meter (only AT) |
|
ABS/VDC Judging |
ABS/VDC |
CAN data input value |
Transmission from vehicle dynamic control (VDC) to high speed control module |
|
ADA Existence Judging |
ON/OFF |
CAN data input value |
Not applicable |
|
Small Light SW |
ON/OFF |
CAN data output value |
ON when small light is illuminated |
|
Headlamp |
ON/OFF |
CAN data output value |
When headlight LO is ON |
|
High Beam |
ON/OFF |
CAN data output value |
When headlight HI is ON |
|
Rr Defogger SW |
ON/OFF |
CAN data input value |
Rear defogger switch ON |
|
Australia Judging Flag |
Australia/Others |
CAN data output value |
|
|
large Diameter Tire |
large Tire/Others |
CAN data output value |
large Tire when the standard tire is 18 in Reception from combination meter |
|
Number of cylinders |
4 Cylinder/6 Cylinder |
CAN data input value |
Display engine equipped |
|
Cam shaft specification |
SOHC/DOHC |
CAN data input value |
Display engine equipped |
|
Turbo |
Turbo/Non-turbo |
CAN data input value |
Display engine equipped |
|
E/G displacement (2.5L) |
2.5 L/ OFF |
CAN data input value |
Display engine equipped |
|
E/G displacement (3.0L) |
3.0 L/ OFF |
CAN data input value |
Display engine equipped |
|
AT Vehicle ID Signal |
ON/OFF |
CAN data input value |
Display transmission equipped |
|
Blower fan information |
ON/OFF |
CAN data input value |
ON when blower fan is operating (always OFF for auto A/C equipped models) |
|
Center display failure |
OK/NG |
CAN data input value |
NG when there is a center display failure Reception from center display (NAVI monitor) |
|
NAVI Failure |
OK/NG |
CAN data input value |
NG when there is a navigation system failure Reception from Center Display |
|
IE Bus failure |
Can not use |
CAN data input value |
Reception from Center Display |
|
Auto A/C failure |
OK/NG |
CAN data input value |
NG when there is a failure in auto air conditioning system Reception from auto A/C module |
|
EBD Warning Light |
OK/OFF |
CAN data input value |
OK when EBD warning light is illuminated Reception from VDC/ABS and transmission to combination meter |
|
ABS Warning Light |
OK/OFF |
CAN data input value |
OK when ABS warning light is illuminated Reception from VDC/ABS and transmission to combination meter |
|
VDC OFF flag |
ON/OFF |
CAN data input value |
Vehicle dynamics control OFF SW is ON Reception from VDC/ABS and transmission to combination meter |
|
VDC/ABS OK B |
OK/NG |
CAN data input value |
NG when there is an error in VDC/ABS system Reception from VDC/ABS |
|
Lighting I Switch Input |
ON/OFF |
Body integrated unit input value |
ON when lighting switch, illumination is ON |
|
Lighting II Switch Input |
ON/OFF |
Body integrated unit input value |
ON when lighting switch, headlight is ON |
|
Dimmer Hi Switch Input |
ON/OFF |
Body integrated unit input value |
ON when dimmer switch is Hi beam position |
|
Dimmer Pass Switch Input |
ON/OFF |
Body integrated unit input value |
ON when dimmer switch is passing position |
|
Lighting I Lamp Output |
ON/OFF |
Body integrated unit output value |
ON when small light is illuminated |
|
Lighting II Lamp Output |
ON/OFF |
Body integrated unit output value |
ON when headlight is illuminated |
|
Lighting Hi Lamp Output |
ON/OFF |
Body integrated unit output value |
ON when Hi beam is illuminated |
|
Front Fog Lamp Output |
ON/OFF |
Body integrated unit output value |
ON when front fog light is ON. |
|
Power Supply Tr |
ON/OFF |
Body integrated unit output value |
Headlight auxiliary power supply ON |
|
Foot Lamp Output |
ON/OFF |
Body integrated unit output value |
ON when foot light is illuminated |
|
Rr defogger op. mode |
Continuous/Normal |
Body integrated unit setting items |
Customize setting |
|
Wiper deicer op. mode |
Continuous/Normal |
Body integrated unit setting items |
Customize setting |
|
Lockout prevention |
ON/OFF |
Body integrated unit setting items |
Customize setting |
|
Automatic locking setup |
ON/OFF |
Body integrated unit setting items |
Customize setting |
|
Auto locking |
ON/OFF |
Body integrated unit setting items |
Customize setting |
|
Door open warning |
ON/OFF |
Body integrated unit setting items |
Customize setting |
|
A/C ECM setting |
ON/OFF |
Body integrated unit setting items |
Customize setting |
|
wiperdeicer |
ON/OFF |
Body integrated unit setting items |
Customize setting |
|
Rear fog light setting |
ON/OFF |
Body integrated unit setting items |
Customize setting |
|
Illumination Control On/Off |
ON/OFF |
Body integrated unit setting items |
Customize setting |
|
Sedan/Wagon Setting |
Sedan/wagon |
Body integrated unit setting items |
Customize setting |
|
MT/AT Setting |
MT/AT |
Body integrated unit setting items |
Customize setting |
|
6MT Setting |
6MT/Other than 6MT |
Body integrated unit setting items |
Customize setting |
|
Destination Setting |
0 — 16 |
Body integrated unit setting items |
— |
|
Factory or Market setting |
Factory/Market |
Body integrated unit setting items |
Customize setting |
|
Off delay time |
OFF, Short, Normal, Long |
Body integrated unit setting items |
Customize setting |
|
Auto lock time |
20, 30, 40, 50, 60 seconds |
Body integrated unit setting items |
Customize setting |
|
Select unlock switch |
Selection/ALL |
Body integrated unit setting items |
Customize setting (only for LHD model with keyless access) |
|
Security setup |
ON/OFF |
Body integrated unit setting items |
Customize setting (only for EK model) |
NOTE:
For detailed operation procedures, refer to “PC application help for Subaru Select Monitor”.